RAILBLAZA TracPort Dash 500
Strength and convenience, married in a 500mm rail equipped with 4 StarPorts and two StarPort adapters for mounting.
Put your own Railblaza accessories together in a convenient, lightweight system.
Then remove the system when you're finished for security, transport or storage.
Included in this pack is:
- 1 TracPort
- 2 x End caps
- 4 x StarPort/TracNut Combos
- Infill cut to length
- 2 x StarPort adapters
- All required fastenings
- Extrusion - Anodised Aluminium
- StarPort AES - Acrylonitrile Ethylene-Styrene
- Gasket: Santoprene
- Accessories 15% Glass-filled nylon
- Stainless Steel Fasteners
- Tape Measure or Rule
- Number 3 phillips Screwdriver
- If mounting centres are other than 100mm (4") you will also require;
- Number 2 pozidrive screwdriver
- Centre punch
- 6.5mm (1/4") drill bit
- Countersink bit (optional)
The TracPort Dash 500 requires 2 StarPorts pre-fitted to the surface or rail it will be mounted on, if these StarPorts are at 100mm (4") centres the pre-drilled mounting holes on the TracPort Dash 500 can be used.
Drilling holes in TracPort [A]:
If the StarPorts on your vessel are not at 100mm (4") centres you will need to drill new mounting holes for the adapters.
Remove end cap screws and take off the end cap [B] from one end, then loosen the screws on the front of the StarPorts and remove enough StarPorts [C] to give access to the TracPort surface, mark and centre punch new drilling points at the same centres as your StarPorts.
Using a 6.5mm (1/4") drill bit, drill through the TracPort, then countersink the holes on the inside, ready for the countersunk screw head.
Fitting the adaptors [D]:
The two supplied adapters come with nuts inserted. Thread the plastic washers onto the screws before inserting bolts through the TracPort and screwing loosely into the adaptors. Place the adaptors into your StarPorts, and then tighten the screws using the Phillips screwdriver.
Fitting the optional Infill Extrusion [E]
The TracPort infill strip is used to trim the extrusion and reduce fouling.
Once your accessories have been mounted, use a sharp knife, scissors or a guillotine to cut strips of infill to length and press them firmly into the extrusion from the front, not slide in from the end.
Shipping rates are automatically calculated based on live quotes supplied by our shipping partners. The quote takes into consideration, the bulk of your cart, where you want it delivered and if you want express or standard shipping.
Get a shipping rate estimate by adding items to your online cart. Go to the cart by clicking on the shopping cart icon located at the top right of the page. Then enter your shipping destination information into the "Estimate Shipping and Tax" section of the shopping cart summary.
We are currently unable to deliver online orders outside of Australia.
If you are located outside of Australia and wish to place an order offline. Please contact our Special Orders Delivery department or send us an enquiry via the orange help bubble located at the bottom right of this page.
Online purchases can be returned/exchanged within 30 days. Some exclusions do apply.
Visit our Returns Policy page for details on how you can return an item.
RAILBLAZA 3 Axis Platform BlackCat. No. 71821Sup. No. 02-4025-11Our Price $42.95
RAILBLAZA Rotating Platform 102mm (4") SquareCat. No. 71819Sup. No. 02-4021-11Our Price $22.95
RAILBLAZA StarPort Extender 150mmCat. No. 71841Sup. No. 03-4016-11Our Price $17.95
SAVE $5.00RAILBLAZA StarPort Kit Black - PairCat. No. 71800Sup. No. 03-4001-11WAS $29.95 now only $24.95
RAILBLAZA Adjustable Platform Kit BlackCat. No. 71810Sup. No. 04-4002-11Our Price $38.95
RAILBLAZA StarPort Kit Black - EachCat. No. 71802Sup. No. 03-4015-11Our Price $17.95
RAILBLAZA DrinkHold BlackCat. No. 71780Sup. No. 02-4048-11Our Price $14.95
RAILBLAZA StarPort Rail Mount 32-41mm Kit BlackCat. No. 71816Sup. No. 03-4013-11Our Price $34.95